
By Ustarminer Engineering Team
Find your Bitaxe's current local IP on its OLED display or in the router's DHCP/client list, then open that numeric address from the same permitted LAN. An old browser bookmark can fail after a lease change even while mining continues.
Confirm that the address belongs to the physical miner before changing settings. This is especially useful when several units have similar names.
Contents

Which address are you looking for?
The address for a local dashboard belongs to your home network. It is different from your internet connection's public address and from the remote mining service's hostname. Typing your home's public address into a browser will not normally open the miner's dashboard.
A router commonly allocates local addresses through DHCP, the service that lends addresses to connected devices. A lease can change after equipment replacement or network reconfiguration. The miner can therefore reconnect successfully while a bookmark still points to its former location.
Also separate numeric addresses from discovery names. The historical firmware announcement describes mDNS, but local-name availability depends on the installed build and network. Engineering’s supported discovery guidance is to read the IP on the OLED or in the router DHCP/client list. Failed name resolution does not prove that mining stopped.
1. Read the OLED or router client list
If the miner displays a local IP, record it. Otherwise use the router's own documented administration route and look for connected clients or DHCP leases. Router menu names differ; you need the current entry for the actual miner.
Compare a second identifier where available, such as a previously recorded hardware address, the display IP or your private inventory. Similar names and old leases can point to another device. Do not edit the first unfamiliar dashboard you find.
A router may retain a disconnected entry until its lease expires. Compare current connection or last-seen information rather than assuming every listed client is live. Resolve disagreement between the display and router before updating the bookmark.
The described 601 hotspot uses its setup page or 192.168.4.1 during initial configuration. After joining Wi-Fi, its router-assigned LAN address serves a different stage. Keep those addresses distinct.
2. Open the numeric address on the permitted LAN
Use the current numeric address with the dashboard access method documented for your firmware. Keep the address inside your private network. You do not need to publish it, add inbound internet forwarding, or expose an administrative interface to find it.
If the router sees the miner but your browser cannot reach it, examine the relationship between the two clients. A phone on a guest network can have internet access while being deliberately prevented from communicating with other local devices. A computer connected through a separate virtual network may face a similar boundary.
A VPN on the management computer can also change routes. Use only a permitted local-management path; do not disable institutional restrictions or assume a work network allows mining equipment. Where a network is deliberately isolated, ask its administrator to provide the supported management arrangement.
3. What does a failed browser connection suggest?
| Observation | Question to investigate | Useful next step |
|---|---|---|
| Numeric address opens; local name fails | Is discovery supported and resolving? | Retain the numeric route and review name support |
| Current router entry; browser fails | Is this the right unit and permitted client path? | Check identity and network isolation |
| No current lease; device powered | Has it joined Wi-Fi and obtained an address? | Check applicable wireless setup and router events |
| Local page opens; service work missing | Is outbound mining correctly configured? | Check jobs, endpoint and receiving identity |
Current Gamma networking supports 2.4GHz WPA/WPA2 and does not join 5GHz-only service. A combined dual-band SSID can still provide a suitable 2.4GHz connection. Check signal and original supply stability when association is unreliable.
A management computer may use a different network route from the miner. Guest-client isolation and VPN routing can affect local access while ordinary internet browsing still works. Use a permitted management path rather than treating those network policies as firmware corruption.
If a normal restart is appropriate, preserve the current evidence first. Repeated factory resets do not help identify whether an old lease, local-name failure or network isolation caused the missing page.
What happens after a router replacement?
In a hypothetical installation, the old router assigned the miner 192.168.1.84. A replacement router uses 192.168.50.0/24 and now assigns 192.168.50.37. The old bookmark fails, although the miner has joined the replacement network and receives mining jobs.
The useful fix is to identify the new lease, open the correct dashboard and update the bookmark. Resetting would remove or disrupt useful configuration without addressing the stale address. These addresses illustrate a scenario; they are not default addresses for a Bitaxe.
After recovery, a router-side DHCP reservation can make future access more predictable if your router supports it. Reserve the address against the correct hardware identity. Avoid choosing an arbitrary static address inside the miner because a collision with another client can create an intermittent problem that is harder to recognize.
4. Verify the device, then keep the new route
Once the page opens, confirm the hardware identity and expected configuration before changing anything. Check uptime, current jobs and recent accepted work. Restored local access does not by itself verify the outbound mining connection.
Update the bookmark and keep the IP with the private device inventory. If your router supports a DHCP reservation, binding it to the correct hardware identity can make future access more predictable. Avoid choosing an arbitrary static address that may collide with another client.
Keep access inside the intended private network. Finding the miner does not require publishing its address or exposing the administrative page through inbound internet forwarding.
The historical Smart Edition setup guide provides its product-management context. Exact App discovery fields and local-name behavior remain version-dependent, so use the OLED and current router record as the practical starting points.
Frequently asked questions
Does a .local name need to work for mining?
Local discovery and outbound mining are separate functions. Check current jobs and accepted work rather than treating one failed name as a mining outage.
Is 192.168.4.1 always the dashboard address?
It is the described 601 setup-hotspot route. After the miner joins the router, use its current LAN address.
Should I reset after the IP changes?
First find and verify the new address. A changed lease can be resolved without erasing a working configuration.
Can two miners have the same displayed name?
Names alone may be ambiguous. Use the current address plus another recorded identifier to reach the intended physical unit.


